Original New PMI Linear Guides MSA20LS MSA20 MSA20LSSSFCN/F0N MSA20LS-N,Height 25mm,Width 44mm,Length 88.8mm,Combination Height 30mm,Blocks Rails Slider Bearings Carriage Guideway Motion Control

★★★★★ 4.9 103 Bewertungen

€18.00
Preis bei Onlinekauf
Kostenloser Versand 30 Tage kostenlose Rückgabe

Verkauft und versendet von agenciacoranto.com.ar
Wir bemühen uns, Ihnen genaue Produktinformationen anzuzeigen. Hersteller, Lieferanten und andere stellen die hier gezeigten Angaben bereit.
€18.00
Preis bei Onlinekauf
Kostenloser Versand 30 Tage kostenlose Rückgabe

Wie möchten Sie Ihren Artikel erhalten?
Die ersten 30 Tage sind kostenlos! Wählen Sie den Tarif an der Kasse.
Versand
Ankunft 25.11.
Kostenlos
Abholung
In der Nähe prüfen
Lieferung
Nicht verfügbar

Verkauft und versendet von agenciacoranto.com.ar
30 Tage kostenlose Rückgabe Details

Produktdetails

Artikelnummer 211200727 Erscheinungsdatum 2026/04/04 Listenpreis €18.00 Modellnummer 211200727
Kategorie

Proper Installation of Linear Guides In this section, we’ll explain in detail how to install linear guides in linear type applications. Step 1: Before mounting the linear guides, a highly recommended advice is to clean up all rough edges and contaminate objects. Important: Datum lines of linear guides are normally composed of antirust. So, brush the antirust with a cleanser before positioning. Spraying some low coherence grease can preserve the datum plane. Step 2: Place the linear guide on the base and secure it with the drive screw or other appliances, so it sits properly on the datum line nicely. Important: Don’t forget to examine the adjustment of the screw holes before tightening them. Tightening the screw forcefully can unalign the screw holes, which influences the accuracy and quality due to offset. Step 3: Sequentially fasten the bolts to make the rail more steady. Push the track against the datum line gently to improve the connection between them. Step 4: Through a torque wrench, tighten the bolts from the centre to both edges. Step 5: Repeat similar strides for installing the auxiliary rail and then install the slides on the rail independently. Don’t forget to gather all adornments, like lubricant fitting, grease fitting and seals in this stage. Otherwise, later on, it gets hard to gather the adornments because of less space. Step 6: Locate the table smoothly on the slides on both main and subsidiary rails. Step 7: Tighten the perpendicular thrust screw to settle the table and attach the table screws in the sequence.

  • Square type with smaller width and can be installed from top side of carriage
  • Rails available:We can cut rails as your request,50-3000MM
  • High Rigidity, Four-way Equal Load
  • Self Alignment Capability
  • Smooth Movement with Low Noise and Interchangeability
Item Weight 13.7 ounces
Manufacturer AEDNX
Item model number MSA20LS
Product Dimensions 3.5 x 1.73 x 0.98 inches

Korrektur der Produktinformationen

Wenn Sie Unvollständigkeiten oder Fehler in den Produktinformationen auf dieser Seite bemerken, nutzen Sie bitte das Korrekturformular unten.

Korrekturanfrage

Kundenbewertungen

4.9 von 5
★★★★★
103 Bewertungen | 42 Rezensionen
So wird die Artikelbewertung berechnet
Alle Bewertungen anzeigen
5 Sterne
89% (92)
4 Sterne
1% (1)
3 Sterne
0% (0)
2 Sterne
0% (0)
1 Stern
10% (10)
Sortieren nach

Für dieses Produkt liegen derzeit keine schriftlichen Bewertungen vor.